pinetime/InfiniTime
1
0
Fork 0
Code Activity
InfiniTime/doc/filesInReleaseNotes.md
Riku Isokoski c2b6a8de3e
Fix markdown format with autoformatter (#1284)
2022-08-21 14:50:09 +03:00

4.1 KiB
Raw Blame History

Using the releases

For each new stable version of IniniTime, a release note is created. It contains a description of the main changes in the release and some files you can use to flash the firmware to your Pinetime.

This page describes the files from the release notes and how to use them.

NOTE : the files included in different Releases could be different. This page describes the release notes of version 0.7.1, which is the version that is pre-programmed for the last batches of pinetimes but will be replaced with 1.0.0 around june 2021.

Files included in the release notes

Standalone firmware

This firmware is standalone, meaning that it does not need a bootloader to actually run. It is intended to be flashed at offset 0, meaning it will erase any bootloader that might be present in memory.

  • pinetime-app.out : Output file of GCC containing debug symbols, useful if you want to debug the firmware using GDB.
  • pinetime-app.hex : Firmware in Intel HEX file format. Easier to use because it contains the offset in memory where it must be flashed, you don't need to specify it.
  • pintime-app.bin : Firmware in binary format. When programming it, you have to specify the offset (0x00) in memory where it must be flashed.
  • pinetime-app.map : Map file containing all the symbols, addresses in memory,...

This firmware must be flashed at address 0x00 in the main flash memory

Bootloader

The bootloader is maintained by lupyuen and is a binary version of this release.

  • bootloader.hex : Firmware in Intel HEX file format.

This firmware must be flashed at address 0x00 in the main flash memory

Graphics firmware

This firmware is a small utility firmware that writes the boot graphic in the external SPI flash memory. You need it if you want to use the bootloader.

  • pinetime-graphics.out : Output file of GCC containing debug symbols, useful is you want to debug the firmware using GDB.
  • pinetime-graphics.hex : Firmware in Intel HEX file format. Easier to use because it contains the offset in memory where it must be flashed, you don't need to specify it.
  • pintime-graphics.bin : Firmware in binary format. When programming it, you have to specify the offset (0x00) in memory where it must be flashed.
  • pinetime-graphics.map : Map file containing all the symbols, addresses in memory,...

This firmware must be flashed at address 0x00 in the main flash memory

Firmware with bootloader

This firmware is intended to be used with our MCUBoot-based bootloader.

  • pinetime-mcuboot-app-image.hex: Firmware wrapped into an MCUBoot image. This is the file that must be flashed at 0x8000 into the flash memory. If the bootloader has been successfully programmed, it should run this firmware after the next reset.

The following files are not directly usable by the bootloader:

  • pinetime-mcuboot-app.out : Output file of GCC containing debug symbols, useful is you want to debug the firmware using GDB.
  • pinetime-mcuboot-app.hex : Firmware in Intel HEX file format.
  • pinetime-mcuboot-app.bin : Firmware in binary format.
  • pinetime-mcuboot-app.map : Map file containing all the symbols, addresses in memory,...

OTA (Update the firmware Over-The-Air)

Once the bootloader and application firmware are running, it is possible to update the current firmware or even replace it with another firmware that uses the same bootloader based on MCUBoot.

NOTE : Use this file only if you programmed our MCUBoot-based bootloader. This file is not compatible with other bootloaders like the one that is based on the closed source NRF SoftDevice !

  • pinetime-app-dfu.zip : This is the file you must provide toNRFConnect to update the firmware over BLE.